Thio-urethane oligomers improve the properties of light-cured resin cements

Ataís Bacchi, Rafael L. Consani, Gedalias C. Martim, Carmem Pfeifer

Research output: Contribution to journalArticle

20 Citations (Scopus)

Abstract

Thio-urethanes were synthesized by combining 1,6-hexanediol-diissocyante (aliphatic) with pentaerythritol tetra-3-mercaptopropionate (PETMP) or 1,3-bis(1-isocyanato-1-methylethyl)benzene (aromatic) with trimethylol-tris-3-mercaptopropionate (TMP), at 1:2 isocyanate:thiol, leaving pendant thiols. Oligomers were added at 10-30 phr to BisGMA-UDMA-TEGDMA (5:3:2, BUT). 25 wt% silanated inorganic fillers were added. Commercial cement (Relyx Veneer, 3M-ESPE) was also evaluated with 10-20 phr of aromatic oligomer. Near-IR was used to follow methacrylate conversion (DC) and rate of polymerization (Rpmax). Mechanical properties were evaluated in three-point bending (ISO 4049) for flexural strength/modulus (FS/FM, and toughness), and notched specimens (ASTM Standard E399-90) for fracture toughness (KIC). Polymerization stress (PS) was measured on the Bioman. Volumetric shrinkage (VS, %) was measured with the bonded disk technique. Results were analyzed with ANOVA/Tukey's test (α = 5%). In general terms, for BUT cements, conversion and mechanical properties in flexure increased for selected groups with the addition of thio-urethane oligomers. The aromatic versions resulted in greater FS/FM than aliphatic. Fracture toughness increased by two-fold in the experimental groups (from 1.17 ± 0.36 MPa m1/2 to around 3.23 ± 0.22 MPa m1/2). Rpmax decreased with the addition of thio-urethanes, though the vitrification point was not statistically different from the control. VS and PS decreased with both oligomers. For the commercial cement, 20 phr of oligomer increased DC, vitrification, reduced Rpmax and also significantly increased KIC, and reduced PS and FM. Thio-urethane oligomers were shown to favorably modify conventional dimethacrylate networks. Significant reductions in polymerization stress were achieved at the same time conversion and fracture toughness increased.

Original languageEnglish (US)
Pages (from-to)565-574
Number of pages10
JournalDental Materials
Volume31
Issue number5
DOIs
StatePublished - May 1 2015

Fingerprint

Resin Cements
Urethane
Oligomers
Polymerization
Cements
Resins
Light
Vitrification
Fracture toughness
Sulfhydryl Compounds
Isocyanates
Methacrylates
Veneers
Mechanical properties
Benzene
Analysis of variance (ANOVA)
Analysis of Variance
Bending strength
Toughness
Fillers

Keywords

  • Mechanical resistance
  • Polymerization stress
  • Resin cements
  • Thio-urethane oligomers

ASJC Scopus subject areas

  • Dentistry(all)
  • Materials Science(all)
  • Mechanics of Materials

Cite this

Thio-urethane oligomers improve the properties of light-cured resin cements. / Bacchi, Ataís; Consani, Rafael L.; Martim, Gedalias C.; Pfeifer, Carmem.

In: Dental Materials, Vol. 31, No. 5, 01.05.2015, p. 565-574.

Research output: Contribution to journalArticle

Bacchi, Ataís ; Consani, Rafael L. ; Martim, Gedalias C. ; Pfeifer, Carmem. / Thio-urethane oligomers improve the properties of light-cured resin cements. In: Dental Materials. 2015 ; Vol. 31, No. 5. pp. 565-574.
@article{75a3dee95b2b40aab8441c3e03ed9e22,
title = "Thio-urethane oligomers improve the properties of light-cured resin cements",
abstract = "Thio-urethanes were synthesized by combining 1,6-hexanediol-diissocyante (aliphatic) with pentaerythritol tetra-3-mercaptopropionate (PETMP) or 1,3-bis(1-isocyanato-1-methylethyl)benzene (aromatic) with trimethylol-tris-3-mercaptopropionate (TMP), at 1:2 isocyanate:thiol, leaving pendant thiols. Oligomers were added at 10-30 phr to BisGMA-UDMA-TEGDMA (5:3:2, BUT). 25 wt{\%} silanated inorganic fillers were added. Commercial cement (Relyx Veneer, 3M-ESPE) was also evaluated with 10-20 phr of aromatic oligomer. Near-IR was used to follow methacrylate conversion (DC) and rate of polymerization (Rpmax). Mechanical properties were evaluated in three-point bending (ISO 4049) for flexural strength/modulus (FS/FM, and toughness), and notched specimens (ASTM Standard E399-90) for fracture toughness (KIC). Polymerization stress (PS) was measured on the Bioman. Volumetric shrinkage (VS, {\%}) was measured with the bonded disk technique. Results were analyzed with ANOVA/Tukey's test (α = 5{\%}). In general terms, for BUT cements, conversion and mechanical properties in flexure increased for selected groups with the addition of thio-urethane oligomers. The aromatic versions resulted in greater FS/FM than aliphatic. Fracture toughness increased by two-fold in the experimental groups (from 1.17 ± 0.36 MPa m1/2 to around 3.23 ± 0.22 MPa m1/2). Rpmax decreased with the addition of thio-urethanes, though the vitrification point was not statistically different from the control. VS and PS decreased with both oligomers. For the commercial cement, 20 phr of oligomer increased DC, vitrification, reduced Rpmax and also significantly increased KIC, and reduced PS and FM. Thio-urethane oligomers were shown to favorably modify conventional dimethacrylate networks. Significant reductions in polymerization stress were achieved at the same time conversion and fracture toughness increased.",
keywords = "Mechanical resistance, Polymerization stress, Resin cements, Thio-urethane oligomers",
author = "Ata{\'i}s Bacchi and Consani, {Rafael L.} and Martim, {Gedalias C.} and Carmem Pfeifer",
year = "2015",
month = "5",
day = "1",
doi = "10.1016/j.dental.2015.02.008",
language = "English (US)",
volume = "31",
pages = "565--574",
journal = "Dental Materials",
issn = "0109-5641",
publisher = "Elsevier Science",
number = "5",

}

TY - JOUR

T1 - Thio-urethane oligomers improve the properties of light-cured resin cements

AU - Bacchi, Ataís

AU - Consani, Rafael L.

AU - Martim, Gedalias C.

AU - Pfeifer, Carmem

PY - 2015/5/1

Y1 - 2015/5/1

N2 - Thio-urethanes were synthesized by combining 1,6-hexanediol-diissocyante (aliphatic) with pentaerythritol tetra-3-mercaptopropionate (PETMP) or 1,3-bis(1-isocyanato-1-methylethyl)benzene (aromatic) with trimethylol-tris-3-mercaptopropionate (TMP), at 1:2 isocyanate:thiol, leaving pendant thiols. Oligomers were added at 10-30 phr to BisGMA-UDMA-TEGDMA (5:3:2, BUT). 25 wt% silanated inorganic fillers were added. Commercial cement (Relyx Veneer, 3M-ESPE) was also evaluated with 10-20 phr of aromatic oligomer. Near-IR was used to follow methacrylate conversion (DC) and rate of polymerization (Rpmax). Mechanical properties were evaluated in three-point bending (ISO 4049) for flexural strength/modulus (FS/FM, and toughness), and notched specimens (ASTM Standard E399-90) for fracture toughness (KIC). Polymerization stress (PS) was measured on the Bioman. Volumetric shrinkage (VS, %) was measured with the bonded disk technique. Results were analyzed with ANOVA/Tukey's test (α = 5%). In general terms, for BUT cements, conversion and mechanical properties in flexure increased for selected groups with the addition of thio-urethane oligomers. The aromatic versions resulted in greater FS/FM than aliphatic. Fracture toughness increased by two-fold in the experimental groups (from 1.17 ± 0.36 MPa m1/2 to around 3.23 ± 0.22 MPa m1/2). Rpmax decreased with the addition of thio-urethanes, though the vitrification point was not statistically different from the control. VS and PS decreased with both oligomers. For the commercial cement, 20 phr of oligomer increased DC, vitrification, reduced Rpmax and also significantly increased KIC, and reduced PS and FM. Thio-urethane oligomers were shown to favorably modify conventional dimethacrylate networks. Significant reductions in polymerization stress were achieved at the same time conversion and fracture toughness increased.

AB - Thio-urethanes were synthesized by combining 1,6-hexanediol-diissocyante (aliphatic) with pentaerythritol tetra-3-mercaptopropionate (PETMP) or 1,3-bis(1-isocyanato-1-methylethyl)benzene (aromatic) with trimethylol-tris-3-mercaptopropionate (TMP), at 1:2 isocyanate:thiol, leaving pendant thiols. Oligomers were added at 10-30 phr to BisGMA-UDMA-TEGDMA (5:3:2, BUT). 25 wt% silanated inorganic fillers were added. Commercial cement (Relyx Veneer, 3M-ESPE) was also evaluated with 10-20 phr of aromatic oligomer. Near-IR was used to follow methacrylate conversion (DC) and rate of polymerization (Rpmax). Mechanical properties were evaluated in three-point bending (ISO 4049) for flexural strength/modulus (FS/FM, and toughness), and notched specimens (ASTM Standard E399-90) for fracture toughness (KIC). Polymerization stress (PS) was measured on the Bioman. Volumetric shrinkage (VS, %) was measured with the bonded disk technique. Results were analyzed with ANOVA/Tukey's test (α = 5%). In general terms, for BUT cements, conversion and mechanical properties in flexure increased for selected groups with the addition of thio-urethane oligomers. The aromatic versions resulted in greater FS/FM than aliphatic. Fracture toughness increased by two-fold in the experimental groups (from 1.17 ± 0.36 MPa m1/2 to around 3.23 ± 0.22 MPa m1/2). Rpmax decreased with the addition of thio-urethanes, though the vitrification point was not statistically different from the control. VS and PS decreased with both oligomers. For the commercial cement, 20 phr of oligomer increased DC, vitrification, reduced Rpmax and also significantly increased KIC, and reduced PS and FM. Thio-urethane oligomers were shown to favorably modify conventional dimethacrylate networks. Significant reductions in polymerization stress were achieved at the same time conversion and fracture toughness increased.

KW - Mechanical resistance

KW - Polymerization stress

KW - Resin cements

KW - Thio-urethane oligomers

UR - http://www.scopus.com/inward/record.url?scp=84927911397&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84927911397&partnerID=8YFLogxK

U2 - 10.1016/j.dental.2015.02.008

DO - 10.1016/j.dental.2015.02.008

M3 - Article

C2 - 25740124

AN - SCOPUS:84927911397

VL - 31

SP - 565

EP - 574

JO - Dental Materials

JF - Dental Materials

SN - 0109-5641

IS - 5

ER -