Influence of different etching modes on bond strength and fatigue strength to dentin using universal adhesive systems

Toshiki Takamizawa, Wayne W. Barkmeier, Akimasa Tsujimoto, Thomas P. Berry, Hidehiko Watanabe, Robert L. Erickson, Mark A. Latta, Masashi Miyazaki

Research output: Contribution to journalArticle

29 Citations (Scopus)

Abstract

Objectives The purpose of this study was to determine the dentin bonding ability of three new universal adhesive systems under different etching modes using fatigue testing. Method Prime & Bond elect [PE] (DENTSPLY Caulk), Scotchbond Universal [SU] (3M ESPE), and All Bond Universal [AU] (Bisco) were used in this study. A conventional single-step self-etch adhesive, Clearfil Bond SE ONE [CS] (Kuraray Noritake Dental) was also included as a control. Shear bond strengths (SBS) and shear fatigue strength (SFS) to human dentin were obtained in the total-etch mode and self-etch modes. For each test condition, 15 specimens were prepared for the SBS and 30 specimens for SFS. SEM was used to examine representative de-bonded specimens, treated dentin surfaces and the resin/dentin interface for each test condition. Results Among the universal adhesives, PE in total-etch mode showed significantly higher SBS and SFS values than in self-etch mode. SU and AU did not show any significant difference in SBS and SFS between the total-etch mode and self-etch mode. However, the single-step self-etch adhesive CS showed significantly lower SBS and SFS values in the etch-and-rinse mode when compared to the self-etch mode. Examining the ratio of SFS/SBS, for PE and AU, the etch-and-rinse mode groups showed higher ratios than the self-etch mode groups. Significance The influence of different etching modes on dentin bond quality of universal adhesives was dependent on the adhesive material. However, for the universal adhesives, using the total-etch mode did not have a negative impact on dentin bond quality.

Original languageEnglish (US)
Pages (from-to)e9-e21
JournalDental Materials
Volume32
Issue number2
DOIs
StatePublished - Feb 1 2016

Fingerprint

Shear Strength
Dentin
Adhesives
Fatigue
Etching
Fatigue testing
Fatigue strength
Resins
Scanning electron microscopy
Tooth

Keywords

  • Dentin bond durability
  • Fatigue strength
  • SEM observation
  • Universal adhesive

ASJC Scopus subject areas

  • Dentistry(all)
  • Materials Science(all)
  • Mechanics of Materials

Cite this

Influence of different etching modes on bond strength and fatigue strength to dentin using universal adhesive systems. / Takamizawa, Toshiki; Barkmeier, Wayne W.; Tsujimoto, Akimasa; Berry, Thomas P.; Watanabe, Hidehiko; Erickson, Robert L.; Latta, Mark A.; Miyazaki, Masashi.

In: Dental Materials, Vol. 32, No. 2, 01.02.2016, p. e9-e21.

Research output: Contribution to journalArticle

Takamizawa, T, Barkmeier, WW, Tsujimoto, A, Berry, TP, Watanabe, H, Erickson, RL, Latta, MA & Miyazaki, M 2016, 'Influence of different etching modes on bond strength and fatigue strength to dentin using universal adhesive systems', Dental Materials, vol. 32, no. 2, pp. e9-e21. https://doi.org/10.1016/j.dental.2015.11.005
Takamizawa, Toshiki ; Barkmeier, Wayne W. ; Tsujimoto, Akimasa ; Berry, Thomas P. ; Watanabe, Hidehiko ; Erickson, Robert L. ; Latta, Mark A. ; Miyazaki, Masashi. / Influence of different etching modes on bond strength and fatigue strength to dentin using universal adhesive systems. In: Dental Materials. 2016 ; Vol. 32, No. 2. pp. e9-e21.
@article{d976d9e84cff4ce3a5d0cdc851364551,
title = "Influence of different etching modes on bond strength and fatigue strength to dentin using universal adhesive systems",
abstract = "Objectives The purpose of this study was to determine the dentin bonding ability of three new universal adhesive systems under different etching modes using fatigue testing. Method Prime & Bond elect [PE] (DENTSPLY Caulk), Scotchbond Universal [SU] (3M ESPE), and All Bond Universal [AU] (Bisco) were used in this study. A conventional single-step self-etch adhesive, Clearfil Bond SE ONE [CS] (Kuraray Noritake Dental) was also included as a control. Shear bond strengths (SBS) and shear fatigue strength (SFS) to human dentin were obtained in the total-etch mode and self-etch modes. For each test condition, 15 specimens were prepared for the SBS and 30 specimens for SFS. SEM was used to examine representative de-bonded specimens, treated dentin surfaces and the resin/dentin interface for each test condition. Results Among the universal adhesives, PE in total-etch mode showed significantly higher SBS and SFS values than in self-etch mode. SU and AU did not show any significant difference in SBS and SFS between the total-etch mode and self-etch mode. However, the single-step self-etch adhesive CS showed significantly lower SBS and SFS values in the etch-and-rinse mode when compared to the self-etch mode. Examining the ratio of SFS/SBS, for PE and AU, the etch-and-rinse mode groups showed higher ratios than the self-etch mode groups. Significance The influence of different etching modes on dentin bond quality of universal adhesives was dependent on the adhesive material. However, for the universal adhesives, using the total-etch mode did not have a negative impact on dentin bond quality.",
keywords = "Dentin bond durability, Fatigue strength, SEM observation, Universal adhesive",
author = "Toshiki Takamizawa and Barkmeier, {Wayne W.} and Akimasa Tsujimoto and Berry, {Thomas P.} and Hidehiko Watanabe and Erickson, {Robert L.} and Latta, {Mark A.} and Masashi Miyazaki",
year = "2016",
month = "2",
day = "1",
doi = "10.1016/j.dental.2015.11.005",
language = "English (US)",
volume = "32",
pages = "e9--e21",
journal = "Dental Materials",
issn = "0109-5641",
publisher = "Elsevier Science",
number = "2",

}

TY - JOUR

T1 - Influence of different etching modes on bond strength and fatigue strength to dentin using universal adhesive systems

AU - Takamizawa, Toshiki

AU - Barkmeier, Wayne W.

AU - Tsujimoto, Akimasa

AU - Berry, Thomas P.

AU - Watanabe, Hidehiko

AU - Erickson, Robert L.

AU - Latta, Mark A.

AU - Miyazaki, Masashi

PY - 2016/2/1

Y1 - 2016/2/1

N2 - Objectives The purpose of this study was to determine the dentin bonding ability of three new universal adhesive systems under different etching modes using fatigue testing. Method Prime & Bond elect [PE] (DENTSPLY Caulk), Scotchbond Universal [SU] (3M ESPE), and All Bond Universal [AU] (Bisco) were used in this study. A conventional single-step self-etch adhesive, Clearfil Bond SE ONE [CS] (Kuraray Noritake Dental) was also included as a control. Shear bond strengths (SBS) and shear fatigue strength (SFS) to human dentin were obtained in the total-etch mode and self-etch modes. For each test condition, 15 specimens were prepared for the SBS and 30 specimens for SFS. SEM was used to examine representative de-bonded specimens, treated dentin surfaces and the resin/dentin interface for each test condition. Results Among the universal adhesives, PE in total-etch mode showed significantly higher SBS and SFS values than in self-etch mode. SU and AU did not show any significant difference in SBS and SFS between the total-etch mode and self-etch mode. However, the single-step self-etch adhesive CS showed significantly lower SBS and SFS values in the etch-and-rinse mode when compared to the self-etch mode. Examining the ratio of SFS/SBS, for PE and AU, the etch-and-rinse mode groups showed higher ratios than the self-etch mode groups. Significance The influence of different etching modes on dentin bond quality of universal adhesives was dependent on the adhesive material. However, for the universal adhesives, using the total-etch mode did not have a negative impact on dentin bond quality.

AB - Objectives The purpose of this study was to determine the dentin bonding ability of three new universal adhesive systems under different etching modes using fatigue testing. Method Prime & Bond elect [PE] (DENTSPLY Caulk), Scotchbond Universal [SU] (3M ESPE), and All Bond Universal [AU] (Bisco) were used in this study. A conventional single-step self-etch adhesive, Clearfil Bond SE ONE [CS] (Kuraray Noritake Dental) was also included as a control. Shear bond strengths (SBS) and shear fatigue strength (SFS) to human dentin were obtained in the total-etch mode and self-etch modes. For each test condition, 15 specimens were prepared for the SBS and 30 specimens for SFS. SEM was used to examine representative de-bonded specimens, treated dentin surfaces and the resin/dentin interface for each test condition. Results Among the universal adhesives, PE in total-etch mode showed significantly higher SBS and SFS values than in self-etch mode. SU and AU did not show any significant difference in SBS and SFS between the total-etch mode and self-etch mode. However, the single-step self-etch adhesive CS showed significantly lower SBS and SFS values in the etch-and-rinse mode when compared to the self-etch mode. Examining the ratio of SFS/SBS, for PE and AU, the etch-and-rinse mode groups showed higher ratios than the self-etch mode groups. Significance The influence of different etching modes on dentin bond quality of universal adhesives was dependent on the adhesive material. However, for the universal adhesives, using the total-etch mode did not have a negative impact on dentin bond quality.

KW - Dentin bond durability

KW - Fatigue strength

KW - SEM observation

KW - Universal adhesive

UR - http://www.scopus.com/inward/record.url?scp=84957849998&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84957849998&partnerID=8YFLogxK

U2 - 10.1016/j.dental.2015.11.005

DO - 10.1016/j.dental.2015.11.005

M3 - Article

VL - 32

SP - e9-e21

JO - Dental Materials

JF - Dental Materials

SN - 0109-5641

IS - 2

ER -